Easy Repair for Chipped Cork Fly Rod Grip
As time goes by, our favorite fishing rods really take a chirapsia, and often the grips go and so worn and chipped that information technology starts to affect your angling. Unless your grips suffer a complete failure, consider these tips for repairing your cork and EVA grips.
This article highlights some common all-time practices for maintaining or repairing your EVA and cork line-fishing rod handles and grips.
Cleaning Existing Cork and EVA Handles
Note: To exist safe, always utilize any recommendations the manufacturer may list, or test on fleck pieces if available – just to brand certain you are happy with the results.
In full general though, here are a few suggestions;
First, y'all tin can try using some warm – lightly soapy – water and a sponge. Gently rub the sponge over the grip and yous may demand a lilliputian more pressure for problem areas. When finished, be sure to use obviously water to wash all the soapy residuum off.
For cork handles – allow the cork dry completely AFTER Awarding.
Then, try applying a sealant like Cork Seal by U-twoscore, it's only about $5.
Cork Seal is designed to seal the surface of cork rod handles. It prevents the penetration of soils and other foreign matter transferred to the grip area from the fisherman'due south easily.
It also enhances that "cork feel" and toughens the cork to aid in the prevention of sloughing and chipping of the cork surface.
Cork Seal soaks into the cork and seals in depth. Once it is dry out – dirt, grime, and fifty-fifty salmon egg residue are hands washed off with soap and water.
Second, we have heard that many fisherman use Mr. Clean eraser pads. Start past getting them little moisture, so gently rub over the cork handle, with a bit more attention to problem areas. Looks like new later.
Again, once the cork handle completely dries, apply cork sealant.
Repairing Existing Cork Handles
Over fourth dimension cork handles tin not only get dirty, just as well dry out and crack – or develop modest areas where the cork may have chipped off.
To fill in those cracks (or even fill up in smaller holes) effort using Elmer'south Carpenter's Wood Filler.
This works splendid on all kinds of cork grips and tin be used to repair and recondition otherwise sorry looking handles.
Some characteristic benefits of using this are:
- Sands easily to a smooth stop
- Resists shrinking + neat
- Easy water clean-upwardly
- Solvent complimentary
Some primal things to keep in mind:
Training: Surface must be clean & dry. Cork, filler and air temperature should be above 40°F.
Filling: Utilise to cork pits and grooves with a spatula, putty knife or similar tool, and be certain to remove any excess. Note: Deeper repairs may need 2 or more fillings.
Sanding: Sand shallow repairs after xv minutes (or when completely dry). Deep repairs may take upwards of ii-8 hours. Employ medium grit sand paper.
Finishing: Before filling, test stain on scrap cork with filler. Apply cork seal or other finish after 24 hours.
You tin can also utilize a heat shrink grip material.
Repairing Existing EVA Handles
When your EVA handles are a mess and the material is fading, the easiest mode to become that handle looking new is to use rut shrink tubing. This of class tin can also be used to repair or upgrade deprecated cork handles too.
Colored Heat Shrink Grip Material by CRB, for instance, comes in a broad variety of colors and sizes, and costs anywhere from $8 to $20.
Heat shrink grip material is a great selection to rejuvenate erstwhile, worn out fishing grips. Information technology works on cork, EVA, Hypalon and even cork tape. It also works extremely well on new customized applications.
The production is generally available in iv sizes to adapt to all applications. It has a soft feel which will reduce fatigue on the angler when fighting fish.
Some typical rod edifice and repair applications and tips for this estrus compress grip cloth are:
- Supervene upon worn out cork, Hypalon and cork tape line-fishing grips
- Apply on saltwater or freshwater rods
- Use on new custom rods
- Use on projects that require a new grip
- Heavy wall thicknesses
- Shrinking temperature of 150° F
- Like shooting fish in a barrel to install with only a heat gun
- Usually has a 2:1 Compress Ratio
Note: Yous may require a rut gun to properly shrink this textile. A Rod Architect's Electrical Oestrus Gun costs about $25 and is usually sold separately.
So don't throw out a perfectly good rod simply because the handle needs repair. Utilise these tips and save your money for bait!
Hope this article was helpful.
Source: https://www.thecustomfisherman.com/repair-your-cork-eva-fishing-rod-handles/
0 Response to "Easy Repair for Chipped Cork Fly Rod Grip"
Post a Comment